Understanding Plumber's Essentials for Bathtub Installation
WebsiteThey are making a few great annotation about How to Install a Bathtub Yourself as a whole in this post which follows.
Setting up a bath tub isn't precisely rocket science, yet it does call for solid plumbing, carpentry, and also in some cases, tiling abilities. Replacing an old bath tub with a new one is additionally a reasonably tough project. If the old bathtub is readily obtainable, the job can relocate rapidly; if you need to open a wall to eliminate the old bathtub and position the new bath tub, the job is much harder. In either case, the job is within a house handyman's abilities, although you will certainly require an assistant to move out the old tub and set in the new one. Make certain you have qualified yourself for the job and are comfortable attempting it. Rather than hiring a specialist to take over a halfway-completed job, it is much better to think about employing one before you start. Opportunities are you might need a professional plumber to make tube links.
This write-up will certainly assist you install a brand-new tub in your restroom if you have already bought a brand-new bathtub as well as do not need to alter the setup of your previous supply of water pipelines.
Your devices and material list should make up the following:
Removing Old Taps
If you need to change old taps with brand-new ones as a part of your setup, then the first thing you need to do is disconnect the water supply. After doing so, switch on the faucets to drain any kind of water continuing to be in the system. The process of getting rid of the existing taps can be rather bothersome due to the restricted accessibility that is typically the instance.
Make use of a basin wrench (crowsfoot spanner) or a tap tool to reverse the nut that attaches the supply pipelines to the faucets. Have a cloth ready for the remaining water that will come from the pipes. When the supply pipes have been eliminated, utilize the exact same tool to loosen the nut that holds the taps onto the bath/basin. You will require to stop the single taps from turning during this procedure. Once the faucets have been eliminated, the holes in the bath/basin will certainly have to be cleaned up of any old sealing substance.
Before carrying on to fit the new taps, compare the pipe links on the old taps to the brand-new taps. If the old faucets are longer than the new taps, after that a shank adapter is required for the brand-new faucets to fit.
Suitable New Taps
If the tails of the new faucets are plastic, then you will certainly need a plastic connector to stop damage to the string. One end of the port fits on the plastic tail of the faucet and the other end supplies a connection to the existing supply pipelines.
If you need to fit a monobloc, after that you will certainly require minimizing couplers, which links the 10mm pipeline of the monobloc to the typical 15mm supply pipe.
Next, position the faucet in the placing hole in the bath/basin making sure that the washing machines remain in area in between the tap and the sink. Secure the tap in place with the manufacturer provided backnut. Once the tap is securely in place, the supply pipes can be connected to the tails of the taps. The taps can either be connected by utilizing corrugated copper piping or with regular tap connectors. The former kind must be connected to the faucet finishes first, tightening only by hand. The supply pipelines can later on be linked to the other end. Tighten both ends with a spanner after both ends have actually been linked.
Setting up the Bathtub
Making use of the two wood boards under its feet, place the tub in the called for position. The wood boards are useful in equally spreading the weight of the tub over the location of the boards instead of focusing all the weight onto 4 tiny factors.
The next goal is to make sure that the bath tub is leveled all round. This can be achieved by checking the spirit level and changing the feet on the tub up until the spirit level reads level.
To install taps, fit all-time low of the outermost adaptable faucet adapter to the ideal supply pipeline by making a compression sign up with; then do the exact same for the other faucet.
Turn on the supply of water as well as examine all joints and also brand-new pipework for leaks and also tighten them if needed. Load the bath tub as well as likewise inspect the overflow outlet and also the typical outlet for leakages.
Ultimately, take care of the bathroom paneling as described in the maker's instruction manual. Tiling and sealing around the bathtub ought to wait till the bath tub has been used at the very least when as this will certainly settle it right into its final setting.
Preparing for the Installment
Firstly, the sustaining structure supplied with the bathroom needs to be fitted (if required) according to the supplier's guidelines. Next off, fit the taps or mixer to the bathtub. When fitting the faucet block, it is essential to make certain that if the faucet features a plastic washing machine, it is fitted between the bathroom and the taps. On a plastic bath, it is also reasonable to fit a sustaining plate under the faucets device to prevent strain on the bath tub.
Fit the versatile faucet ports to the bottom of both taps using 2 nuts as well as olives (often provided with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet opening, and afterwards pass the electrical outlet through the hole in the bath. Make use of the nut provided by the manufacturer to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipe.
Next, fit the end of the adaptable overflow pipeline to the overflow electrical outlet. After that, screw the pipeline to the overflow face which ought to be fitted inside the bathroom. See to it you use every one of the provided washing machines.
Connect the catch to the bottom of the waste electrical outlet on the bathtub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the trap to the electrical outlet. Link the bottom of the overflow tube in a comparable manner.The bathroom should now prepare to be fitted in its last position.
Tiling Around the Tub
In the location where the bath meets the tile, it is necessary to seal the accompanies a silicone rubber caulking. This is very important as the fitting can relocate sufficient to fracture a stiff seal, triggering the water to permeate the wall surface between the bathroom and the tiling, bring about problems with moisture and also feasible leakages to the ceiling listed below.
You can choose from a variety of coloured sealers to blend in your components and also installations. They are offered in tubes and cartridges, and are capable of sealing spaces as much as a width of 3mm (1/8 inch). If you have a larger void to fill up, you can load it with spins of drenched newspaper or soft rope. Bear in mind to constantly fill the tub with water prior to sealing, to enable the movement experienced when the bathtub remains in use. The sealer can break relatively very early if you do not consider this motion before sealing.
Alternatively, ceramic coving or quadrant ceramic tiles can be made use of to edge the bath or shower tray. Plastic strips of coving, which are easy to use and cut to dimension, are additionally conveniently readily available on the market. It is a good idea to fit the floor tiles using water-resistant or water resistant sticky as well as grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
As a person who reads about How to Install a Bathtub Yourself, I imagined sharing that excerpt was important. Do you know about someone else who is in the market for the niche? Why not promote it. We love reading our article about Tools You Need to Install a New Bathtub .
Get Your Estimate Now